1.2.7.nnn - System Settings - B

Device Reset Occurred Notification Control - Property 1.2.7.1.1.1

Property Description
Property OID	1.2.7.1.1.1 / 0x010207010101
Name	Device Reset Occurred Notification Control
Description	The device uses this property to control behavior of the Device Reset Occurred notification in Notification 0x1001 - Device Information Update. Changes to this property do not take effect until the device is power cycled or reset.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Binary
Valid Values	0x00 = Never send this notification. 0x01..0xFE = The frequency in seconds the device should repeat sending the notification until the host requests that it stop with Property 1.2.7.1.1.2 Device Reset Occurred Notification Acknowledged. 0xFF = Only send this notification once.
Default	0x00

Device Reset Occurred Notification Control - Get Request Example

Example (Hex)
AA 00 81 04 01 55 D1 01 84 0F D1 01 85 01 01 87 04 02 07 01 01 89 02 C1 00

Device Reset Occurred Notification Control - Get Response Example

Example (Hex)
AA 00 81 04 82 55 D1 01 82 04 00 00 00 00 84 82 00 10 D1 01 85 01 01 87 04 02 07 01 01 89 03 C1 01 00

Device Reset Occurred Notification Control - Set Request Example

Example (Hex)
AA 00 81 04 01 55 D1 11 84 10 D1 11 85 01 01 87 04 02 07 01 01 89 03 C1 01 05

Device Reset Occurred Notification Control - Set Response Example

Example (Hex)
AA 00 81 04 82 55 D1 11 82 04 00 00 00 00 84 82 00 10 D1 11 85 01 01 87 04 02 07 01 01 89 03 C1 01 05

Device Reset Occurred Notification Acknowledged - Property 1.2.7.1.1.2

Property Description
Property OID	1.2.7.1.1.2 / 0x010207010102
Name	Device Reset Occurred Notification Acknowledged
Description	The host can use this property to acknowledge it has received the Device Reset Occurred notification in Notification 0x1001 - Device Information Update and to request that the device stop sending it. Alternatively, because the device automatically sets the value of this property to 0x00 on boot, the host can use this property to detect power cycles or resets using a polling method. To implement this, the host should read the value on a set schedule (for example, every 2 seconds). If the host finds a value of 0x00, a power cycle or reset has occurred, and the host should set the value back to 0x01. From that point until the next power cycle or reset, the value will remain 0x01. Changes made to this property will not persist after a power cycle or reset. After a power cycle or reset, this property has a value of 0x00 until the host changes it to 0x01.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Binary
Valid Values	0x00 = Not acknowledged. Only the device can set to this value. 0x01 = Acknowledged. Do not continue to send the notification.
Default	0x00

Device Reset Occurred Notification Acknowledged - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070101 8902 C200

Device Reset Occurred Notification Acknowledged - Get Response Example

Example (Hex)
AA00 8104 8255D101 8204 00000000 84820010 D101 8501 01 8704 02070101 8903 C201 00

Device Reset Occurred Notification Acknowledged - Set Request Example

Example (Hex)
AA00 81040155D111 8410 D111 8501 01 8704 02070101 8903 C20101

Device Reset Occurred Notification Acknowledged - Set Response Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820010 D111 8501 01 8704 02070101 8903 C201 01

Device Reset Will Occur Soon Notification Control - Property 1.2.7.1.1.3

Property Description
Property OID	1.2.7.1.1.3 / 0x010207010103
Name	Device Reset Will Occur Soon Notification Control
Description	The host can use this property to control behavior of the Device Reset Will Occur Soon notification in Notification 0x1001 - Device Information Update. See 24 Hour Automatic Reset PCI Requirement for more information. Changes to this property do not take effect until the device is power cycled or reset.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Binary
Valid Values	0x00 = Never send this notification. 0x01..0xFF = Number of minutes before a reset to send the notification message.
Default	0x03

Device Reset Will Occur Soon Notification Control - Get Request Example

Example (Hex)
AA 00 81 04 01 55 D1 01 84 0F D1 01 85 01 01 87 04 02 07 01 01 89 02 C3 00

Device Reset Will Occur Soon Notification Control - Get Response Example

Example (Hex)
AA 00 81 04 82 55 D1 01 82 04 00 00 00 00 84 82 00 10 D1 01 85 01 01 87 04 02 07 01 01 89 03 C3 01 05

Device Reset Will Occur Soon Notification Control - Set Request Example

Example (Hex)
AA 00 81 04 01 55 D1 11 84 10 D1 11 85 01 01 87 04 02 07 01 01 89 03 C1 01 05

Device Reset Will Occur Soon Notification Control - Set Response Example

Example (Hex)
AA 00 81 04 82 55 D1 11 82 04 00 00 00 00 84 82 00 10 D1 11 85 01 01 87 04 02 07 01 01 89 03 C1 01 05

Auto Reset Configuration - Property 1.2.7.1.1.4

Property Description
Property OID	1.2.7.1.1.4 / 0x010207010104
Name	Auto Reset Configuration
Description	This property controls the device’s auto reset feature. The auto reset feature can be configured such that the device automatically resets 23 hours after booting up or at a specific time of day. Or device can be configured to enter a restricted mode after 24 hours without a reset or power down. When device enters restricted mode it will respond to first command received with Response Message - Request Handler: Group 0x02, Subgroup 0x01, Code 0x1D. Device then sends Notification 0x1001 – Device Information Update: Category 0x00, Reason 0x01 - Reset will occur soon. Device will then auto reset. The auto-reset feature cannot be disabled. See 24 Hour Automatic Reset PCI Requirement for more information. Changes to this property do not take effect until the device is power cycled or reset.
Securing Key	None
Min. Len (b)	2
Max. Len (b)	2
Data Type	Binary
Valid Values	First byte 0 - 23 hours and second byte 0 - 59 minutes = Reset at the time of day specified. The time of day specified should be 24-hour Universal Time Coordinated (UTC). For example, values of 0 0 would be 12:00am UTC and values of 23 59 (0x17 0x3B) would be 11:59pm UTC. First byte 0xFF and second byte 0xFF = Auto reset 23 hours after booting up. First byte 0xEE and second byte 0xEE = Device enters Restricted Mode 24 hours after booting up.
Default	0xFF 0xFF

Auto Reset Configuration - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070101 8902 C400

Auto Reset Configuration - Get Response Example

Example (Hex)
AA0081048255D10182040000000084820011D1018501018704020701018904C402FFFF

Auto Reset Configuration - Set Request Example

Example (Hex)
AA00 81040155D111 8411 D111 8501 01 8704 02070101 8904 C402 FFFF

Auto Reset Configuration - Set Response Example

Example (Hex)
AA0081048255D11182040000000084820011D1118501018704020701018904C402FFFF

User Event Notification Controls Enable - Property 1.2.7.1.2.1

Bit Property Description
Property OID	1.2.7.1.2.1 / 0x010207010201
Name	User Event Notifications Enable
Description	The host can use this property to enable notification reasons defined in Notification 0x1001 - Device Information Update in the User Events Category. Each bit enables a specific Reason by setting that bit to 1. Byte 0 is the first byte, bit 0 is the LSB of each byte. The device only detects these user events and sends these notifications when it is idle. While processing a command (not idle), such as when processing a transaction with Command 0x1001 - Start Transaction, the device only sends notifications related to the command it is currently processing. Notification reasons may consume power when idle. For example, enabling Contactless reasons requires the device to continuously consume some radio frequency power to detect the presence of a contactless card when idle. To conserve power, only enable the notification reasons that are required by the solution design, if any. The readers and their associated notifications will be disabled if the battery charge is 5 percent or lower. Changes to this property do not take effect until the device is power cycled or reset.
Securing Key	None
Min. Len (b)	4
Max. Len (b)	4
Data Type	Binary
Valid Values	Byte 0 · bit 0 = Reason: Contactless Card Presented · bit 1 = Reason: Contactless Card Removed · bit 2 = Reason: Card Seated in Slot · bit 3 = Reason: Card Unseated from Slot · bit 4 = Reason: Card Swiped · bit 5 = Reason: Touch Sensor Press Detected · bit 6 = Reason: Touch Sensor Release Detected · bit 7 = Reason: Barcode Read Detected Byte 1 · bit 0 = Reason: Encrypt Barcode Reader Event Data · bit 1 = Reserved (set to 0x00) · etc. Byte 2 · bit 0 = Reserved (set to 0x00) · etc. Byte 3 · bit 0 = Reserved (set to 0x00) · etc. Any byte / bit not listed here is reserved for future use. The host should set those values to 0, so if a future revision of firmware starts using those bits, the related notifications will be disabled and will not affect the existing host software.
Default	0x00, 0x00, 0x00, 0x00 (all User Event notifications disabled)

User Event Notification Controls Enable - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070102 8902 C100

User Event Notification Controls Enable - Get Response Example

Example (Hex)
AA00 8104 8255D101 8204 00000000 84820013 D101 8501 01 8704 02070102 8906 C1 04 00 00 00 00

User Event Notification Controls Enable - Set Request Example

Example (Hex)
AA00 8104 0155D111 8413 D111 8501 01 8704 02070102 8906 C1 04 03 00 00 00

User Event Notification Controls Enable - Set Response Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820013 D111 8501 01 8704 02070102 8906 C1 04 03 00 00 00

User Event Notification MSR Data Timeout (MSR Only) - Property 1.2.7.1.2.2

Bit Property Description
Property OID	1.2.7.1.2.2 / 0x010207010202
Name	User Event Notification MSR Data Timeout
Description	This parameter defines the number of seconds the device waits for the host to take action (by sending Command 0x1001 - Start Transaction) after the device sends Notification 0x1001 - Device Information Update to report a User Event / Card Swiped event. After this period of time passes, the device erases the buffered card data from memory. Changes to this property do not take effect until the device is power cycled or reset.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Binary
Valid Values	· 0x00 = Invalid value. (will be converted to 0x02 in the firmware) · 0x01 to 0xFF = 1 to 255 seconds
Default	0x02 (2 seconds)

User Event Notification MSR Data Timeout (MSR Only) - Get Request Example

Example (Hex)
AA00 8104 010CD101 841A D101 8107 2B06010401F609 8501 01 890A E208E706E104E202C200

User Event Notification MSR Data Timeout (MSR Only) - Get Response Example

Example (Hex)
AA00 8104 820CD101 8204 00000000 8482001B D101 8107 2B06010401F609 8501 01 890B E209E707E105E203C2 0102

User Event Notification MSR Data Timeout (MSR Only) - Set Request Example

Example (Hex)
AA00 8104 010DD111 841B D111 8107 2B06010401F609 8501 01 890B E209E707E105E203C2 0102

User Event Notification MSR Data Timeout (MSR Only) - Set Response Example

Example (Hex)
AA00 8104 820DD111 8204 00000000 8482001B D111 8107 2B06010401F609 8501 01 890B E209E707E105E203C2 0102

Maximum Battery Charge Level (Deprecated) - Property 1.2.7.1.3.1

Property Description
Property OID	1.2.7.1.3.1 / 0x010207010301
Name	Maximum Battery Charge Level
Description	This OID has been deprecated. The OID can be written or read but it will have no effect of the device’s behavior. The host can use this property to control the maximum charge level for the battery. All charge percentages reported or displayed will use this percentage as 100% charged. Setting this value to lower than 0x64 (100%) will increase the life of the battery but reduce the run time when running from the battery. The Maximum Battery Charge Level takes effect immediately after the host changes it.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Binary
Valid Values	0x0A..0x64
Default	0x64 (100%) if WLAN device 0x50 (80%) for all other devices

Maximum Battery Charge Level (Deprecated) - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070103 8902 C100

Maximum Battery Charge Level (Deprecated) - Get Response Example

Example (Hex)
AA00 8104 8255D101 8204 00000000 84820010 D101 8501 01 8704 02070103 8903 C101 50

Maximum Battery Charge Level (Deprecated) - Set Request Example

Example (Hex)
AA00 81040155D111 8410 D111 8501 01 8704 02070103 8903 C101 50

Maximum Battery Charge Level (Deprecated) - Set Response Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820010 D111 8501 01 8704 02070103 8903 C101 50

Device Low Temperature Notification Level - Property 1.2.7.1.4.1

Property Description
Property OID	1.2.7.1.4.1 / 0x010207010401
Name	Device Low Temperature Notification Level
Description	The device will send a low temperature notification when the device’s temperature falls below this temperature. The temperature is in degrees Celsius. The Device Low Temperature Notification Level takes effect immediately after the host changes it.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Signed Binary
Valid Values	Temperature in Celsius: DynaProx: 0xE2 .. 0x55 (-30 .. 85) DynaProx BCR: 0xEC .. 0x37 (-20 .. 55) DynaFlex: 0x00 .. 0x2D (0 .. 45) This value must be less than that set in 1.2.7.1.4.2.
Default	Temperature in Celsius: DynaProx: 0xE2 (-30 DynaProx BCR: 0xEC (-20) DynaFlex: 0x00 (0)

Device Low Temperature Notification Level - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070104 8902 C100

Device Low Temperature Notification Level - Get Response Example

Example (Hex)
AA00 8104 8255D101 8204 00000000 84820010 D101 8501 01 8704 02070104 8903 C101 00

Device Low Temperature Notification Level - Set Request Example

Example (Hex)
AA00 81040155D111 8410 D111 8501 01 8704 02070104 8903 C101 05

Device Low Temperature Notification Level - Set Response Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820010 D111 8501 01 870402070104 8903 C101 05

Device High Temperature Notification Level - Property 1.2.7.1.4.2

Property Description
Property OID	1.2.7.1.4.2 / 0x010207010402
Name	Device High Temperature Notification Level
Description	The device will send a high temperature notification when the device’s temperature rises above this temperature. The temperature is in degrees Celsius. The Device High Temperature Notification Level takes effect immediately after the host changes it.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Signed Binary
Valid Values	Temperature in Celsius: DynaProx: 0xE2 .. 0x55 (-30 .. 85) DynaProx BCR: 0xEC .. 0x37 (-20 .. 55) DynaFlex: 0x00 .. 0x2D (0 .. 45) This value must be greater than that set in 1.2.7.1.4.1.
Default	Temperature in Celsius: DynaProx: 0x55 (85) DynaProx BCR: 0x37 (55) DynaFlex: 0x2D (45)

Device High Temperature Notification Level - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070104 8902 C200

Device High Temperature Notification Level - Get Response Example

Example (Hex)
AA00 8104 8255D101 8204 00000000 84820010 D101 8501 01 8704 02070104 8903 C201 2D

Device High Temperature Notification Level - Set Request Example

Example (Hex)
AA00 81040155D111 8410 D111 8501 01 8704 02070104 8903 C201 2D

Device High Temperature Notification Level - Set Response Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820010 D111 8501 01 870402070104 8903 C201 2D

Device Temperature Notification Repeat Interval - Property 1.2.7.1.4.3

Property Description
Property OID	1.2.7.1.4.3 / 0x010207010403
Name	Device Temperature Notification Repeat Interval
Description	While the device’s temperature is outside of the range defined by Device Low Temperature Notification Level (1.2.7.1.4.1) and Device High Temperature Notification Level (1.2.7.1.4.2), notifications will be sent to the host. This property sets the period between notifications. The Device Temperature Notification Repeat Interval takes effect immediately after the host changes it.
Securing Key	None
Min. Len (b)	1
Max. Len (b)	1
Data Type	Binary
Valid Values	0x00 Send once. Do not repeat. 0x0F .. 0xFF Repeat period in seconds. Must be multiple of 0x0F (15).
Default	0x1E (30 seconds)

Device Temperature Notification Repeat Interval - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070104 8902 C300

Device Temperature Notification Repeat Interval - Get Response Example

Example (Hex)
AA00 8104 8255D101 8204 00000000 84820010 D101 8501 01 8704 02070104 8903 C301 1E

Device Temperature Notification Repeat Interval - Set Request Example

Example (Hex)
AA00 81040155D111 8410 D111 8501 01 8704 02070104 8903 C301 1E

Device Temperature Notification Repeat Interval - Set Response Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820010 D111 8501 01 870402070104 8903 C301 1E

Enable Barcode Types - Property 1.2.7.1.5.1

Property Description
Property OID	1.2.7.1.5.1 / 0x010207010501
Name	Enable Barcode Types
Description	This property specifies the types (symbologies) of barcodes that the BCR will detect and read.
Securing Key	None
Min. Len (b)	4
Max. Len (b)	4
Data Type	Binary
Valid Values	Byte 0 - bit 0: Code128 Byte 0 - bit 1: GS1-128 (UCC/EAN-128) Byte 0 - bit 2: EAN-8 Byte 0 - bit 3: EAN-13 Byte 0 - bit 4: UPC-E Byte 0 - bit 5: UPC-A Byte 0 - bit 6: Interleaved 2 of 5 Byte 0 - bit 7: ITF-14 Byte 1 - bit 0: ITF-6 Byte 1 - bit 1: Matrix 2 of 5 Byte 1 - bit 2: Code 39, Code 32 Byte 1 - bit 3: Codabar Byte 1 - bit 4: Code 93 Byte 1 - bit 5: AIM 128 Byte 1 - bit 6: ISSN Byte 1 - bit 7: ISBN Byte 2 - bit 0: Industrial 25 Byte 2 - bit 1: Standard 25 Byte 2 - bit 2: Plessey Byte 2 - bit 3: Code 11 Byte 2 - bit 4: MSI Plessey Byte 2 - bit 5: GS1 Databar (RSS) Byte 2 - bit 6: PDF417 Byte 2 - bit 7: QR Code Byte 3 - bit 0: Aztec Byte 3 - bit 1: Data Matrix Byte 3 - bit 2: Micro QR
Default	0x7F 0x0E 0xE0 0x06 – (values shown in bold above enabled) Changes to this property will be applied permanently and will not be overwritten in the event of a reset, FW update, etc.

Enable Barcode Types - Get Request Example

Example (Hex)
AA00 8104 0155D101 840F D101 8501 01 8704 02070105 8902 C100

Enable Barcode Types - Get Response Example

Example (Hex)
AA00 8104 8255D101 8204 00000000 84820013 D101 8501 01 8704 02070105 8906 C104 7F0EE006

Enable Barcode Types - Set Request Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820010 D111 8501 01 870402070104 8903 C301 1E

Enable Barcode Types - Set Response Example

Example (Hex)
AA00 8104 8255D111 8204 00000000 84820013 D111 8501 01 8704 02070105 8906 C104 7F0EE006