Property ID:
0x6E
Property Type:
Byte
Length:
1 byte
This property controls the masking of the service code on ISO card tracks 1 and 2. If this property is set to 1, the device masks the service code. If this property is set to 0, the device does not mask the service code.
The host can use this property to enable Selectable Card Data Encryption. Any of the bits in this property enables the SCDE with the corresponding data field included in the encrypted SCDE.
The M002 message is transmitted to the host instead of the M001 message when the following four conditions are met when a financial card is swiped.
Any of the defined property 0x78 bits are set to 1 (enabled)
Card Encode Type of the swiped card is ISO
Initial SCDE DUKPT Key was injected into the device
For security purposes, the reader will reset itself once a day. You can choose what time this reset will occur by changing this property. Set the value to HHMM in Coordinated Universal Time (UTC). HH is one byte with a value of 0-23. MM is one byte with a value of 0-59 The new value takes effect after the next device reset or power cycle.
This data is stored securely (encrypted by DDEK). The data gets sent out in encrypted form using DUKPT when the device is in QWANTUM Mode, the button is enabled, and the button is pressed.
For PCI certified devices, this value will match the one found on the PCI website and the product label.
This property indicates whether the firmware was built to use production device keys (005454) or test device keys (000101).
The primary functions of device states are to inform production software about completed steps and pending tasks. It serves as a checklist and can also assist with remote services and RMAs.
If a key has been loaded into the device, then it’s bit indicator should be set to 1.
A fully loaded reader would return a keymap of: 7E 00 07 00 8C 00 00 00.
The host can use this property to adjust the device’s USB packet delay. The property can be set to 0 to have no delay, or it can be set to a specific value in the range of 1 to 255 ms.
Adjusting this value does not require security when the device is fully configured.
Adjusting this value does not affect the USB HOST POLL TIMEOUT, PROPERTY 0x52. In fact, it is mostly independent from the polling interval.
MagTek recommends the following values for various platforms:
Windows = 0x00 (0 ms)
Android = 0x19 (25 ms)
Linux = 0x32 (50 ms)
Get Property:
Yes
Set Property:
Yes
Default Value:
0x01
Property ID:
0x78
Property Type:
Binary
Length:
1 byte
Get Property:
Yes
Bit Number
Description of Bit
Bit 0
Card Holder Name
0 = Disable (Default)
1 = Enable
Bit 1
PAN
0 = Disable (Default)
1 = Enable
Bit 2
Expiration Date
0 = Disable (Default)
1 = Enable
Property ID:
0x80
Property Type:
String
Length:
varies
Get Property:
Yes
Example
10PCI50U0BA
Property ID:
0x81
Property Type:
Byte
Length:
1 byte
Get Property:
Yes
Property ID:
0x82
Property Type:
Byte
Length:
2 bytes
Get Property:
Yes
Length
Field Name
Value
1
Hour
Value from 0x00...0x17 (0-23)
1
Minute
Property ID:
0x83
Property Type:
Bytes
Length:
0-1023 bytes
Get Property:
Yes (Secure MAC)
Property ID:
0x84
Property Type:
String
Length:
varies
Get Property:
Yes
Property ID:
0x85
Property Type:
Binary
Length:
3 bytes
Get Property:
Yes
Property ID:
0x86
Property Type:
Binary
Length:
4 bytes
Get Property:
Yes
Byte
Type
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bytes
Bits
Name
Settings
BYTE 1 – System State
Bit 7
Offline
0 = All bits in this property are set to 0
1 = Not all bits in this property are 0
Property ID:
0x87
Property Type:
Binary
Length:
8 bytes
Get Property:
Yes
Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Property ID:
0x88
Property Type:
Binary
Length:
1 byte
Get Property:
Yes
Note – Test firmware can only allow test keys to be injected.
Note that the device is considered offline (no card reading) until all 4 bytes are zero.
Set Property:
Yes (Secure MAC)
Default Value:
0x00
Bit 3
Service Code
0 = Disable (Default)
1 = Enable
Bit 4
T1 Discretionary Data
0 = Disable (Default)
1 = Enable
Bit 5
T2 Discretionary Data
0 = Disable (Default)
1 = Enable
Bit 6
Reserved
Bit 7
Reserved
Set Property:
No
Default Value:
N/A
Set Property:
Yes (Secure MAC)
Default Value:
0
• 0 = Normal Operation
• 1 = QWANTUM Mode
Set Property:
Yes (New value takes effect after reset)
Default Value:
0000 (UTC Midnight)
Value from 0x00...0x3B (0-59)
Set Property:
Yes (Secure MAC)
Default Value:
Length = 0
Set Property:
No
Standard Value:
'iDynamo 5 Gen III'
Set Property:
No (Value depends on firmware build type)
Default Value:
005454 (for PCI), 000101 (for Non-PCI)
Set Property:
No – values come from self-test and security status.
Default Value:
N/A
Bit 0
1
System State
Offline
0
0
Device Keys missing
RTC not active/set
Not Initialized
Security Inactive
Tampered
2
Self-Test failure
Data Integrity
Key Integrity
0
0
0
Registers
Crypto
RNG
3
PCI Info
0
0
0
0
0
HW ID Missing
Model Name Missing
Serial # Missing
4
Unmapped Data Types
0
0
0
0
0
0
0
0
Bit 6
Reserved
Always 0
Bit 5
Bit 4
Device Keys Missing
0 = Device keys present
1 = Device keys missing
NOTE: “Device Keys” refer to the keys that are injected during MfgCfg such as Transport Keys and MAC Keys. “Device Keys” do not include DUKPT keys (2007, 2002 and 2003). The DUKPT keys are “Financial Keys”.
Bit 3
RTC not Active/Set
0 = RTC active
1 = RTC inactive (not enabled)
Bit 2
Not Initialized
0 = Non-volatile storage initialized
1= Non-volatile storage not initialized
NOTE: “Initialized” means:
a. the master keys are generated internally.
b. the data & key storage area is initialized with an initialization indicator such as 0xAA55 and its integrity is known good.
Bit 1
Security Inactive
0 = Security activated
1= Security not activated
NOTE: “Security” means Tamper.
Bit 0
Tampered
0 = Device not tampered
1 = Device tampered
BYTE 2 – Self-Test Failure
Bit 7
Data Integrity
0 = Configuration data in NVS not corrupted
1 = Found data corruption in the configuration data
Bit 6
Key Integrity
0 = All fixed keys and injected keys are not corrupted
1 = Found key data for one or more keys is corrupted
Bit 5
Reserved
Always 0
Bit 4
Bit 3
Bit 2
Registers
0 = All hardware registers in uC required for normal operation of the device are initialized/ enabled/configured/ functional;
1 = Any one or more of those registers are not operating correctly
Bit 1
Crypto
0 = Passed test
1 = Failed test
NOTE: Enable Crypto engine in uC and test crypto functions and make sure it returns the expected results. (e.g. KAT – Known Answer Test)
Bit 0
RNG
0 = Passed test
1 = Failed test
NOTE: Enable RNG in uC and read RNG value a few times and make sure RNG returns different values for each read.
BYTE 3 – PCI Info
Bit 7
Reserved
Always 0
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
PCI HW ID Missing
0 = Found a valid PCI HW ID in Property 0x80
1 = PCI HW ID missing
Bit 1
Model Name Missing
0 = Found a valid model name in Property 0x84
1 = Model name missing
Bit 0
Serial # Missing
0 = Found a valid DSN in Property 0x03
1 = DSN missing
BYTE 4 – Unmapped Data Types
Bit 7
Reserved
Always 0
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Set Property:
No – values come from key injection.
Starting Value:
0 – if no keys loaded
1 – TK1
0
MKIFTK
MFGTK
PRODTK
FINTK
DEVTK
MTK
TMPTK
2 – TK2
0
0
0
0
0
0
0
0
3 – MK1
0
0
0
0
0
MFRQMK
MREQMK
FREQMK
4 – MK2
0
0
0
0
0
0
0
0
5 – DK1
DKPTM7
0
0
0
DKPTM3
DKPTM2
0
0
6 – DK2
0
0
0
0
0
0
0
0
7 – DK3
0
0
0
0
0
0
0
0
8 – DK4
DKPTM1F
0
0
0
0
0
0
0
Set Property:
Yes
Starting Value:
0x00 (0 ms)